Frequently Asked Questions For Kirby Owners

A: This is your Neutral/Drive pedal. When you are vacuuming or using the carpet shampooer in the upright position, push down the Drive (D) pedal. This activates Tech Drive® power assist to make pushing your Kirby easy.
‍
For the balance of product usage (i.e. cleaning hard floor surfaces, vacuuming in canister mode with attachment hose, vacuuming in hand held mode, using air pump, turbo accessory, etc.) push down the Neutral (N) pedal.

A: There is a fill line on the disposable bag and when the dirt reaches this line you should replace your disposable bag because it is no longer filtering properly. Be sure to utilize only Genuine Kirby filter bags, available here to ensure your Kirby system is cleaning properly.

A: We do not suggest you wash the outer bag or get it wet.

A: There are a few reasons this may be happening. The vacuum might not be set at the proper height. If the nozzle is too high off the floor, the brush will not reach the floor to clean it properly. To adjust the height, simply press the toe touch pedal on the side of the unit.
Another reason may be because the brush roll is not turning.

If the brush roll indicator light on the nozzle is not on, that could mean the following: the brush roll isn’t turning freely or the belt is slipping, broken or not engaged. To engage the brush roll, flip out the belt lifter handle and turn it clockwise until the green arrows line up.
‍
Lastly, you might have a full bag. Check the disposable filter bag to see if it’s full and replace it if it is.

A: No. Do not use your Kirby to get water off the floor or out of carpet.

Watch Engineering Manager John Lackner explain how to prevent misalignment issues while installing the brush roll in the Kirby Multi-Surface Shampoo System.

A: First and foremost, only use genuine Kirby carpet shampoo with your system. Unscrew the large cap from the shampoo tank and use it to measure carpet shampoo. Do not use the cap from the bottle of the shampoo to measure.

For a small room, fill the tank with water to the first line on the side of the tank and add one capful of shampoo. To clean a large room, fill the tank to the third line and add three capfuls of shampoo.

A: To produce foam properly, the suds screen and foam sponge must be in place on the shampoo tank. To check this, remove the tank and make sure they’re properly in place.

A: This could be for one of two reasons. The suds screen and/or foam sponge are not in place. If not in place, this would allow too much water to dispense, over-wetting your carpet.
‍
Repeatedly cleaning the same area would also cause this. To avoid over-wetting moving forward, allow the system to dispense a layer of foam on the carpet and then turn the valve on the shampoo tank to OFF before going back over the area to work in the foam and scrub the carpet.

A: Check to make sure you have both your suds screen and sponge in. The suds screen goes in the small hole on the tank, the hose goes over it and the sponge goes in the large hole on the tank.

A: Please check out thi, with instructions on how to change the belt.

A: To remove the power nozzle, or front head of the vacuum, first make sure the unit is turned off and is unplugged. Press the Toe-Touch pedal all the way down. Then, raise the headlight hood, pull the belt lifter handle toward you and turn it counterclockwise until the red arrows line up.

Once the read arrows are lined up, turn the Accessory Lock counterclockwise, which will release the Power Nozzle. Now you may remove the nozzle and attach your next accessory and lower the hood.To re-attach the power nozzle, follow the steps above to remove the attached accessory.

Once that is off, the belt on the Power Nozzle should be stretched on the hook inside. (If it is not, flip out the belt lifter handle and turn it counterclockwise until the red arrows line up. The hook should catch and stretch the belt inside.) Rest the two hooks on the rear of the Power Nozzle over the attaching bar on the front of the vacuum.

Then push the nozzle against the unit and turn the Accessory Lock clockwise to lock in place. Flip out the belt lifter handle and turn it clockwise until the green arrows line up. This will release the belt from the hook to spin the brush roll.

A: First, make sure the unit is plugged in, and then check that the accessory connected to the unit is properly attached. Depending on what attachment you’re using, make sure the Power Nozzle, Hose, Carpet Shampoo System or Air Intake Guard is properly attached.

Then, check to see if the Mini Emptor, Shampoo Take, or Hose is properly attached to the side. If those are all connected properly, your unit should turn on.

A: You can purchase replacement parts and supplies here . You can also call Breeze Living at 1300 834 141.

We suggest using Flitz metal polish.

A:It is likely the belt isn’t turning freely on the brush roll. Flip out the belt lifter handle and turn it clockwise until the green arrows line up.

This will release the belt from the hook in order to turn freely on the brush roll. Make sure to check the brush roll for tangled hairs or debris that may be preventing it from turning.

A: There are two safety switches on your Kirby.

One is on the front of the unit and one is on the side where the bag attaches. If there is nothing attached to the front of the unit, such as your floor nozzle, attachment hose or shampoo system, the Kirby will not turn on. This is to prevent injury to you from the fan and prevent damaging the fan.

There is also a safety switch on the side of the unit where the bag attaches, or the tank if you are shampooing. If the mini emptor or tank is not snapped tightly against the Kirby you will not have power. You need to remove the bag or tank and put it back on again and make sure it snaps tightly into place.

A:  Please contact Breeze Living at 1300 834 141.

A: The owner manuals for all Kirby systems are available here.

To determine the manufacturing date of your cleaning product, locate the date code that has been printed on the bottle.

Next, use the guide below to determine the manufacturing date for your bottle of cleaning supplies.

‍DATE CODE CONVENTION
‍“A(Y)(DDD)”A, B, (…) = 1^st batch passed that day, 2^nd batch passed that day, (…)
‍
(Y) = last digit of the year juice passed
‍
(DDD) = Julien date of day juice passed

‍EXAMPLE
‍A0001 would be the first batch passed on the date 1/1/2020.